12.10 Further reading
Open full view...Categories: Finishes & Corrosion
Introduction
The documents listed below have been classified as follows
- Key References
- CWCT Publications
- British Standards
- Other Standards
- Other References
Some but not all of of these documents are referred to in the sections of this package. Key references generally cover a significant proportion of the subject matter of the package in greater detail than presented here. Other references generally relate to a small part of the subject matter of the package; they range from short papers to text books. No attempt has been made to compile a comprehensive bibliography but where a literature search has been carried out for other purposes the list of other references is extensive. British Standards include European and ISO Standards adopted as British Standards. It should be noted that British Standards are updated from time to time and that in this updating process they are being replaced by European Standards. The Standards listed may not necessarily be the most up to date version. The current status of Standards can be checked using the BSI online catalogue at www.bsi.org.uk . Other Standards include standards published by other national standards organisations and standards produced by recognised societies and institutions.
Key References
DORAN D. K., 1992, Construction materials reference book, Butterworth Heinemann,
ADDLESON L. and RICE C., 1991, Performance of mateials in buildings: a study of the principles and agencies of change, Butterworth Heinemann
CWCT Publications
CWCT, 1996, Guide to good practice for facades, Centre for Window and Cladding Technology, University of Bath, 44pp.
HARRIS R. and KEILLER A., 1999, Durability of facades: A scoping study, Centre for Window and Cladding Technology, University of Bath, 56pp.
British Standards
BS 729, 1971, Specification for hot dip galvanized coatings on iron and steel articles, British Standards Institution, (replaced by BS EN ISO 1461).
BS 1178, 1982, Specification for milled lead sheet for building purposes, British Standards Institution.
BS 1186: Timber for and workmanship in joinery
Part1: Specification for timber has been replaced by BS EN 942:1996: Timber in joinery. General classification of timber quality
Part 2:1988: Specification for workmanship
Part 3:1990: Specification for wood trim and its fixing
BS 1282: 1975: Guide to the choice and application of wood preservatives
BS 1449 Steel plate, sheet and strip Part 2, 1983, Specification for stainless and heat-resisting steel plate, sheet and strip, British Standards Institution, (mainly replaced by BS EN 10088).
BS 1706, 1990, Method of specifying Electroplated coatings of zinc and cadmium on iron and steel, British Standards Institution.
BS 3987, 1991, Specification for Anodic oxidation on wrought aluminium for external architectural applications, British Standards Institution.
BS 4842, 1994, Specification for liquid organic coatings for application to aluminium alloy extrusions, sheet and preformed sections for external architectural purposes, and for the finish on aluminium alloy extrusions, sheet and preformed sections coated with liquid organic coatings, British Standards Institution.
BS 4921, 1988, Specification for sherardized coatings on iron or steel, British Standards Institution.
BS 5250, 1995, Code of practice for control of condensation in buildings, British Standards Institution.
BS 5268: Structural use of timber. Part 5:1989: Code of practice for the preservative treatment of structural timber
BS 5427, Code of practice for the use of profiled sheet for roof and wall cladding on buildings, Part 1, 1996, Design, British Standards Institution.
BS 5589:1989: Code of practice for preservation of timber
BS 5950, Structural use of steelwork in building, British Standards Institution.
BS6270-3:1991 Code of practice for cleaning and surface repair of buildings. Part 3 Metals (Cleaning only), British Standards Institution
BS 6338, 1982, Specification for chromate conversion coatings on electroplated zinc and cadmium coatings, British Standards Institution.
BS3987, 1991, Specification for anodic oxidation coatings on wrought aluminium for external architectural applications, British Standards Institution
BS 6496, 1984, Specification for powder organic coatings for application and stoving to aluminium alloy extrusions, sheet and preformed sections for external architectural purposes, and for the finish on aluminium alloy extrusions, sheet and preformed sections coated with powder organic coating, British Standards Institution.
BS 6497, 1984, Specification for powder organic coatings for application and stoving to hot-dip galvanised hot-rolled steel sections and preformed steel sheet for windows and associated external architectural purposes, and for the finish on galvanized steel sections and preformed sheet coated with powder organic coatings, British Standards Institution.
BS 6651:1985 Code of practice for protection of structures against lightning, British Standards Institution
BS 6915, 1988, Specification for design and construction of fully supported lead sheet roof and wall coverings, British Standards Institution.
BS 8000:Workmanship on building sites. Part5:1990: Code of practice for carpentry, joinery and general fixing
BS 8118,Structural use of aluminium,
Part 1: 1991, Code of practice for design,
Part 2 1991, Specification for materials workmanship and protection, British Standards Institution.
BS8221-1:2000 Code of practice for cleaning and surface repair of buildings. Part 1 Cleaning of natural stones, brick, terracotta, and concrete, British Standards Institution
CP 143: Code of practice for sheet roof and wall coverings,
Part 1: 1958, Aluminium corrugated and troughed,
Part 10: 1973 Galvanised corrugated steel, British Standards Institution.
Part 12: 1988, Copper,
Part 15: 1986, Aluminium, British Standards Institution.
BS EN 485: 1994, Aluminium and aluminium alloys - Sheet, strip and plate, British Standards Institution.
BS EN 515: 1993, Aluminium and aluminium alloys - Wrought products - Temper, British Standards Institution.
BS EN 573: 1995, Aluminium and aluminium alloys - Chemical composition and form of wrought product, British Standards Institution.
BS EN 755: 1997, Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles, British Standards Institution
BS EN 1172: 1997: Copper and Copper alloys: Sheet and Strip for Building purposes, British Standards Institution.
BS EN 1412: 1996: Copper and Copper alloys - European numbering system, British Standards Institution.
BS EN 10027 Designation systems for steels
Part 1, 1992, Steel names, principal symbols,
Part 2, 1992, Numerical system,
British Standards Institution.
BS EN 10088 Stainless steels,
Part 1, 1995, List of stainless steels,
Part 2, 1995, Technical delivery conditions for sheet/plate and strip for general purposes,
Part 3, 1995, Technical delivery conditions for semi finished products, bars, rods and sections for general purposes, British Standards Institution.
BS EN 10142, 1991, Specification for continuously hot-dip zinc coated low carbon steel and strip for cold forming: Technical delivery conditions, British Standards Institution.
BS EN 10143, 1993, Continuously hot-dip metal coated steel sheet and strip. Tolerances on dimensions and shape, British Standards Institution.
BS EN 10147, 1992, Specification for continuously hot-dip zinc coated structural steel sheet and strip. - Technical delivery conditions, British Standards Institution.
BS EN 10169, Continuously organic coated (coil coated) steel flat products, Part 1, 1997, General information (definitions, materials, tolerances, test methods) British Standards Institution.
BS EN 10214:1995. Continuously hot-dip zinc-aluminium (ZA) coated steel strip and sheet - Technical delivery conditions, British Standards Institution.
BS EN 10215:1995. Continuously hot-dip aluminium-zinc (AZ) coated steel strip and sheet - Technical delivery conditions, British Standards Institution.
BS EN 22063, 1994, Metallic and other inorganic coatings. Thermal spraying. Zinc, aluminium and their alloys, British Standards Institution.
BS EN ISO 1461, 1999, Hot dip galvanised coatings on fabricated iron and steel articles - Specification and test methods, British Standards Institution.
Other Standards
AAMA 605 Voluntary Specification for high performance organic coating on architectural aluminium extrusions and panels, American
Architectural Manufacturers Association.
AASC Metal Finishing Specifications, Architectural Advisory Service Centre.
Other References
Aluminium finishing association, 1999, Finishing aluminium.a guide for architects
BRE Digest 139, 1972, Control of lichens, moulds and similar growths
BRE Digest 304, 1985, Preventing decay in external joinery
BRE Digest 305, 1986, Zinc-coated steel, Digest 305, Building Research Establishment.
BRE Digest 307, 1986, Identifying damage by wood-boring insects
BRE Digest 327, 1987, Insecticidal treatment against wood-boring insects
BRE Digest 378 (1993) Wood preservatives: application methods
BRE Digest 387 (1993) Natural finishes for exterior wood
BRE Digest 393 (1994) Specifying wood treatments: the new European approach
BRE Digest 407 (1995) Timber for joinery
BRE Digest 415, 1996, Reducing the risk of pest infestations in buildings
BRE Digest 418, 1996, Bird, bee and plant damage to buildings
BRE Digest 422 (1997) Painting exterior wood
BRE Digest 428,1997, Protecting buildings against lightning,
BRE Digest 429(1998) Timbers: their natural durability and resistance to preservative treatment
BRE Digest 431(1998) Parts 1 and 2 (1998) Hardwoods for joinery and construction
BRE Digest 440(1999) Weathering of white external pvc-u
BRE Digest 442(1999) Architectural use of polymer composites
BRE IP 20/87 External joinery: end grain sealers and moisture control
BRE IP 11/95 Control of biological growths on stone
Wernick S, Pinner P and Sheasby P G, 1987, The surface treatment and finishing of aluminium and its alloys 5th edition, Finishing publications Ltd